mLRS MAVLink 900MHz TX Module KIT, mR900-30-TX

mLRS (MAVLink long range system) firmware, 900 MHz LoRa, 30 dBm RF power

Warning

MATEKSYS mLRS 900MHz series using SX126x/STM32WLE5 LoRa chip are NOT compatible with ELRS 900MHz / Frsky R9 series using the SX127x. They will not bind with each other.

https://github.com/olliw42/mLRS-docu/blob/master/docs/SX126x_SX127x_INCOMPATIBILITY.md

LoRa chip SX126x(e.g. mR900-30, E22) and STM32WLE5xx(e.g. mR900-22, WIO-E5, E77) are compatible with each other.

Specifications

mR900-30
- STM32G431KB, mLRS firmware
- LoRa SX1262 with TCXO
- PA/LNA SKY68383-11
- RF Frequency: 900MHz (868MHz, 915MHz FCC)
- 915MHz RF power: 21dBm(min) / 22dBm / 24dBm / 27dBm / 30dBm(1000mW)
- 868MHz RF power: 24dBm(min) / 24dBm / 24dBm / 27dBm / 30dBm(1000mW)
- Antenna connector: IPEX MHF-1 to SMA
mRx-Tx Adapter
- Built-in HC-04 Bluetooth module
- Built-in 5V fan controller, running if output power>=500mW
- TX2: RC IN(CRSF)
- one buttom for DFU mode and Bind
- Red and Green LED for mLRS status
- Blue LED for Bluetooth status
- Power supply: 5-13V DC @ JR_PIN3 (VIN)

Packing:
- 1x mR900-30-TX,
- 1x IPEX MHF1 to SMA adapter cable 5cm,
- 1x IPEX MHF1 to RP-SMA adapter cable 5cm
- 1x 5V Fan (25*25*10mm) and some screws
- no SMA antenna & 3D printed Case packed
Downloads:
- JR Bay Case 3D print (stl)
- mRX-TX Adapter 3D (step)

LED Status

[Red flashing 2Hz], not connected to transmitter
[Green flashing 1Hz], connected to transmitter
[Red and Green alternately ], Binding mode enabled

Binding

After powering on, press the bind button (for ca. 4 seconds) on the receiver. When in bind mode, the green and red LEDs will blink alternatively with ca 2.5 Hz.
https://github.com/olliw42/mLRS-docu/blob/master/docs/BINDING.md

Firmware

mLRS https://github.com/olliw42/mLRS/tree/main/firmware/pre-release-stm32
Target: tx-matek-mr900-30-g431kb-default

Tips

mLRS Github & Documentation
mLRS Discord
mLRS Facebook group
MATEKSYS mLRS 900MHz series are NOT compatible with ELRS 900MHz & Frsky R9 series using the SX127x. They will not bind with each other.

Routing and layout

Firmware flashing

Download STM32CubeProgrammer from ST website

https://www.st.com/en/development-tools/stm32cubeprog.html

mLRS firmware:

https://github.com/olliw42/mLRS/tree/main/firmware/pre-release-stm32
Targets: tx-matek-mr900-30-g431kb-default

————————————————————————————————————

Make sure STM DFU driver has been installed. Check out “Install DFU Drivers” in this page

Connect the TX module USB to computer while holding the boot button in.

Select USB
USB1 and click Refresh
Connect
select “Erasing & Programming”
Tick all sectors and click “erase selected sectors”
Browse firmware (hex or bin file) related to the hardware.
Click “Start Programming”
After programming, unplug USB and plug USB back in. If red LED blinks at 2Hz, the TX module is waiting for connecting with receiver.

lua

https://github.com/olliw42/mLRS/tree/main/lua

The mLRS Lua script provides the most convenient way to change the Tx and Rx module’s settings.

The Lua script works on both OpenTx and EdgeTx radios but there are two different versions depending on the display of your radio:

If your radio has a 480×272 color screen (e.g. Jumper T16, Radiomaster TX16S) then use the “mLRS.lua” file
If your radio has a black and white screen (e.g. Frsky Taranis X9E, Radiomaster Zorro) then use the “mLRS-bw.lua” file

Note: The mLRS script requires EdgeTx version 2.9.x or later.

Setup

Three things need to be done in order to use the Lua script:

The Tx module must be configured for CRSF or mBridge mode, by setting the parameter “Tx Ch Source” to “crsf” or “mbridge” respectively. Since firmware version v0.2.13 “crsf” is the default setting, so this will be already completed after an initial flash. If not, the CLI needs to be used to set this parameter accordingly, as described in CLI Commands.
In EdgeTX/OpenTX, navigate to MDL->MODEL SETUP and configure the external RF module for CRSF or mBridge protocol with 400K baud rate.
- Note: mLRS only officially supports 400K baud rate.
The Lua script “mLRS.lua” or “mLRS-bw.lua” located in the “lua” folder of the repository needs to be copied to the “SCRIPTS/TOOLS” folder of the radio’s SD card. One can follow the common tutorials for how to do this.

You should then be able to run the Lua script by going to SYS->TOOLS on the radio, and selecting “mLRS Configurator”.

Resellers